Level 1 sweep and inspection to the NFPA 211 annual standard - flue, crown, cap, and flashing checked and photographed
Chimney sweep logs do not sweep chimneys. They loosen some creosote - which then falls where a brush and vacuum still have to collect it.
Before
After
Before
After
Before
AfterOlympia Chimney Chimney Cap & Crown in Roanoke: What to Know First
As an independent Olympia Chimney service provider in Roanoke, we install, replace, and repair chimney caps and crowns on Olympia Chimney systems, with most jobs completed in a single visit and upfront pricing agreed before we start. A standard cap installation or crown coating runs $280-$620 depending on flue count and access, and we carry common Olympia Chimney hardware so you’re not waiting on shipping. This page is for homeowners who already know they have an Olympia Chimney product and want a technician who understands the line’s quirks, not a generalist guessing at the parts. Call (540) 787-3302 for a free estimate. A clean chimney doesn’t announce itself. Neither does a problem - until it does.
How Olympia Chimney Products Fail - and How We Fix Them
- Olympia Chimney 304 stainless multi-flue caps: The cross-breaks in the lid flatten over Roanoke’s freeze-thaw cycles, pooling water that rusts the base rail from the inside out. We see this on homes in Raleigh Court and Grandin Village where the original cap looked fine from the ground. We replace with a heavier-gauge lid or switch to a Gelco cap with reinforced breaks, depending on your flue spacing.
- Olympia Chimney single-flue caps with mesh sides: The 5/8-inch mesh on earlier production runs clogs with cottonwood seed in May and June, especially near the Roanoke River greenway. The cap suffocates the flue, backing smoke into the house. We clean the mesh in place when possible, or upgrade to a 3/4-inch mesh Olympia cap that breathes better during shedding season.
- Olympia Chimney gel-coated galvanized caps: The gel coat chalks and cracks after seven to ten years of southwest Virginia sun exposure, exposing the galvanized shell to pinhole rust. We’ve pulled these off houses in South Roanoke where the homeowner thought the cap was “fine” until water stained the firebox. We strip and coat with a compatible crown sealant, or replace with a 304 stainless unit if the substrate is too far gone.
- Olympia Chimney crown wash systems: The factory-formulated crown mix shrinks differently than Portland-based pours common in Roanoke masonry, creating hairline cracks at the flue interface within three to five years. Water follows the flue tile down into the smoke chamber. We grind back to sound material and apply a flexible crown coating rated for the thermal cycling these crowns see.
- Olympia Chimney wind-band adapters: The set-screw mounting on oval flue adapters loosens in Roanoke’s spring wind events, tilting the cap and opening the flue to driven rain. We’ve found caps hanging by one screw on houses in Wasena after a March storm. We reseat with stainless tap bolts and a bead of high-temp silicone, or fabricate a custom skirt if the flue tile is irregular.
Our Olympia Chimney Chimney Cap & Crown Process
- 1
Call and schedule. A live person answers, 24 hours a day. We ask for your Olympia Chimney model if you know it, and whether you’re seeing water, draft issues, or visible damage.
- 2
Level-2 camera inspection. Our technician arrives uniformed and background-checked. We run a camera up the flue, photograph the crown from the roof, and show you what we found. No verdict without evidence you can see.
- 3
Parts decision. If your cap is still in production, we quote OEM Olympia Chimney hardware. If it’s discontinued, we source quality aftermarket from Gelco or Famco that matches your flue dimensions and draft requirements. We explain the trade-off, and you decide.
- 4
The repair. Most cap replacements and crown coatings take two to four hours. We protect your roof and landscaping, remove the failed component, install the new, and verify clearance and mesh spec.
- 5
Test and document. We run a draft test, check for leaks with a water simulation, and give you photos of the completed work with a plain-English summary.
- 6
The guarantee. Everything is covered by our 90-Day Done Right Promise - in writing, no arguing. If it’s not right, we come back.
What Olympia Chimney Chimney Cap & Crown Costs in Roanoke
| Service | Typical Range | What Moves the Price |
|---|---|---|
| Single-flue cap replacement (OEM Olympia Chimney) | $280-$420 | Flue tile shape, mesh size, roof pitch |
| Multi-flue cap replacement (OEM or Gelco) | $380-$620 | Span width, leg height, wind band needed |
| Crown coating (Olympia Chimney-compatible) | $340-$580 | Crown square footage, crack depth, prep required |
| Crown partial rebuild with coating | $580-$940 | Extent of spalling, flue tile reset needed |
| Custom cap fabrication (discontinued models) | $440-$780 | Material (galvanized vs. stainless), complexity |
Steep roofs, slate or tile that requires special footing, and chimneys over 35 feet add labor. We give you the full number before booking, and that number is the number on the invoice. Call (540) 787-3302 for an exact quote - estimates are free.
Why Roanoke Homeowners Call Hearthstone Chimney Co. for Olympia Chimney Work
We’ve been on roofs in Roanoke since 1984. Russell Haines and our crew have handled Olympia Chimney products long enough to know which part numbers interchange, which don’t, and when a Gelco or Famco cap solves the problem better than waiting on back-ordered OEM stock. Our 90-Day Done Right Promise means if the crown coating cracks or the cap seal fails, we come back - in writing, no arguing. Photos you can see, a plain-English verdict. Done right, and we stand behind it.
FAQs
No. As an independent Olympia Chimney service provider, we use OEM or equivalent parts and document our work. Manufacturer warranties on materials remain intact; our labor carries its own 90-Day Done Right Promise. Call (540) 787-3302 if you have warranty paperwork you’d like us to review.
A 304 stainless Olympia Chimney cap typically lasts 15 to 20 years in Roanoke’s climate; galvanized models average 8 to 12 years before significant rust. Proximity to the Blue Ridge Parkway and higher elevations with more freeze-thaw cycles shorten that by a few seasons. We inspect and tell you honestly whether yours has another winter in it.
We stock common hardware, and our supply chain includes Gelco and Famco adapters that fit Olympia Chimney flue profiles. For truly odd sizes, we measure and fabricate a custom cap in galvanized or stainless. Most solutions are available within a week; rush orders are possible for active leaks.
If the crown has surface cracks and solid concrete beneath, a coating is the right call. If it’s spalling more than a quarter-inch deep, or the flue tile has shifted, partial rebuild is necessary. We show you the camera footage and explain which category you’re in, with no pressure to do more than the chimney needs.
We book inspections within a few days, and most cap and crown jobs are completed in a single visit once parts are confirmed. During peak burning season (October through January), schedule two weeks ahead if possible. Call (540) 787-3302 for current availability - a live person answers.
Written by Russell Haines, Owner, Hearthstone Chimney Co. at Hearthstone Chimney Co., serving Roanoke and nearby areas.